HY 5-P

Current Transducer HY 5 ... 25-P For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. Electrical data RoHS since date code ● Hall effect measuring principle ● Insulation voltage 2500 V � ● Compact design for PCB mounting ● Low power consumption ● Extended measuring range (3 × IP N) ● Insulating plastic case recognized according to UL 94-V0. 5 ±15 ⌀ 0.7 10 ±30 ⌀ 1.1 12.5 ±37.5 ⌀ 1.4 15 ±45 ⌀ 1.4 20 ±60 2 × ⌀ 1.2 1) 25 ±75 2 × ⌀ 1.4 1) Uout HY 5-P 45260 HY 10-P 45286 HY 12-P 45264 HY 15-P 45276 HY 20-P 46097 HY 25-P 45269 Output voltage (Analog) @ IP N, RL = 10 kΩ, TA = 25 ° C ±4 Insulation resistance @ 500 V DC Load resistance Output internal resistance Supply voltage (±5 %) 2) Current consumption 50 × IP N > 1000 MΩ > 1 kΩ 100 Ω ±12 ... 15 V ±10 mA ÎP max Primary withstand peak current (1 ms) RINS RL Rout UC IC = 5 ... 25 A Features Primary nominal Primary current Primary Type RMS current measuring range conductor IP N (A) IP M (A) (mm) IP N V Accuracy - Dynamic performance data ε Error @ IP N, TA = 25 ° C (excluding offset) < ±1 % εL Linearity error 3) (0 .. ±IP N) < ±1 % of IP N TCUO E Temperature coefficient of UO E typical ±1.5 mV/K max ±3 mV/K TCUout Temperature coefficient of Uout (% of reading) < ±0.1 %/K UO E Electrical offset voltage @ TA = 25 °C < ±40 mV UO M Magnetic offset voltage @ IP = 0, after an excursion of 1 × IP N < ±15 mV tD 90 Delay time to 90 % of the final output value for IP N step 4) HY 25-P < 5 µs others < 3 µs BW Frequency bandwidth (−3 dB) 5) DC ... 50 kHz General data TA Ambient operating temperature TA st Ambient storage temperature m Mass Standard 6) Advantages ● Easy mounting ● Small size and space saving ● Only one design for wide current ratings range ● High immunity to external interference. Applications ● Static converters for DC motor drives ● Switched Mode Power Supplies (SMPS) ● AC variable speed drives ● Uninterruptible Power Supplies (UPS) ● Battery supplied application ● General purpose inverters. Application Domain ● Industrial. −10 ... +80 °C −25 ... +85 °C < 14 g EN 50178: 1997 Notes: 1) Conductor terminals are soldered together 2) Operating at ±12 V ≤ UC < ±15 V will reduce measuring range 3) Linearity data exclude the electrical offset 4) For a di/dt = 50 A/µs 5) Please refer to derating curves in the technical file to avoid excessive core heating at high frequency 6) Please consult characterisation report for more technical details and application advice. 74.73.08.000.0, 74.73.13.000.0, 74.73.14.000.0, 74.73.15.000.0, 74.73.17.000.0, 74.73.19.000.0 7July2020/Version 10 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 1/3 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com Current Transducer HY 5 ... 25-P Insulation coordination U d UNm RMS voltage for AC insulation test, 50 Hz, 1 min Rated insulation RMS voltage 2.5 500 1) kV V Note: 1) Pollution class 2, overvoltage category III. Safety This transducer must be used in limited-energy secondary circuits according to IEC 61010-1. This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (e.g. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/3 7July2020/Version 10 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com Dimensions HY 5 25-P (in(inmm) Dimensions HY.. 5..25-P mm. 1 mm = 0.0394 inch) 36.0 Max. HY 5 to 15-P 32.0 Max. JA PAN 12 Max. 18.0 12.0 HY 5-P 45059 HY 10 - P JP2 9639 ( d) (0.5) 3 x 2.54 10±0.3 1 2 3 4 5 HY 20 to 25-P ( PIN ARRANGEMENT 1 +15V 2 --15V 3 OUTPUT Connection 4 0V dx2) 1 +15 V 2 -15 V 3 OUTPUT 4 0 V 5 PRIMARY IN 6 PRIMARY OUT 5 PRIMARY IN 6 PRIMARY OUT 8.5±0.3 10±0.3 Pins Arrangement 3.9±0.3 6 HY 20 - P 9639 3±0.5 3 x 2.54 (0.3) (a)±0.3 8.5±0.3 PCB MOUNTING DIMENSIONS (in mm ±0.1, hole -0, +0.2) 2 holes dia. (e) HY 5 to15-P 3 x 2.54 10 8.5 HY 20 to 25-P (g) 3 x 2.54 Type holes dia (e) 4 holes dia 1 10 (g) 8.5 HY HY HY HY HY HY 05-P 10-P 12-P 15-P 20-P 25-P a mm 1.1 1.4 1.5 1.5 1.4 1.5 d mm 0.7 1.1 1.4 1.4 1.2 1.4 e mm 1.2 1.6 2.0 2.0 1.8 2.0 g mm ----1.4 1.6 Safety Remark This transducer must be used in electric/electronic equipment ● Temperature of the primary conductor should not exceed 100°C. with respect to applicable standards and safety requirements in accordance with the following manufacturer's operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/2 061027/8 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Page 3/3 7July2020/Version 10 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com